- Why are my logs not burning?
- How do I stop my wood burning stove from going black?
- Can logs be too dry to burn?
- Why is the glass on my pellet stove turning black?
- How do you know if logs are seasoned?
- Is black soot from gas fireplace dangerous?
- How do you make logs burn slower?
- Can you leave the door open on a wood burning stove?
- Can wood be too old to burn?
- How do you clean soot?
- Why does my propane fireplace glass turns black?
Why are my logs not burning?
While the most common causes of log burners going out are insufficient oxygen, fuel or heat, stoves also rely on a properly functioning chimney.
The purpose of this is to draw out exhaust fumes that could suffocate your fire..
How do I stop my wood burning stove from going black?
Try burning harder woods like oak, cherry, or walnut, and avoid burning woods known for their higher sap content. If your wood stove has a heat setting, try turning the heat controls up a few notches. Hotter fires will keep your glass cleaner. Allow enough oxygen to vent into your wood stove.
Can logs be too dry to burn?
Kiln-dried wood is down around 10 percent moisture. Depending on climate and conditions of storage, normal firewood won’t dry down to kiln-dried moisture because of normal outdoor humidity. … Above 30% water bubbles from the end grain when the wood is heated and it is very hard to burn at all.
Why is the glass on my pellet stove turning black?
If you’re experiencing blackened glass, it can most likely be fixed with one tweak. Your problem could be caused by a lack of air flow. The exhaust fan works to suck air out through the burn pot to cause combustion of the pellets, which is hindered by a leaky gasket. …
How do you know if logs are seasoned?
To identify well seasoned wood, check the ends of the logs. If they are dark in colour and cracked, they are dry. Dry seasoned wood is lighter in weight than wet wood and makes a hollow sound when hitting two pieces together. If there is any green colour visible or bark is hard to peel, the log is not yet dry.
Is black soot from gas fireplace dangerous?
Improper Airflow can cause excessive buildup of soot. … Making sure your gas fireplace is cleaned and inspected can not only prevent soot which can stick to your walls and windows of your fireplace, but prevent safety issues such as carbon monoxide poisoning, and combustion of soot which could cause a chimney fire.
How do you make logs burn slower?
Make your fire last longer. Light it upside down.When setting the fire, put a layer of large logs across the bottom.Then put logs above, but in the opposite direction.Then a layer of smaller logs above this.Then layer of sticks in the opposite direction.Then two layers of dry kindling, each in opposite directions.More items…•
Can you leave the door open on a wood burning stove?
Wood burning stoves are not designed to be used with the door open. You can use a wood burning stove with the door open but doing so will lose the control of the air flow into the stove, making it operate less efficiently and sending more heat up the chimney rather than out into the room.
Can wood be too old to burn?
Firewood shouldn’t be able to age past its usefulness for burning. In other words, if the firewood is protected from insects and moisture reasonably well, it could last for many years before burning. … If it sounds solid, and hasn’t turned to a log-shaped piece of termite poop or compost, you can burn it.
How do you clean soot?
Basic Directions:Use a vacuum, dry cleaning sponges, and/or Absorene Wall Cleaner to dry clean any surfaces that have soot on them. … Wet clean surfaces using either PRS Fire and Content Cleaner (diluted per label instructions), or Unsmoke Degrease-All diluted at 14-43 oz per gallon of water.More items…
Why does my propane fireplace glass turns black?
Propane fireplaces can become sooty for two main reasons: improper air-to-fuel ratio or bad fuel. The air-to-fuel ratio can be changed by malfunction or an obstruction of the tank regulator, primary air shutter or the flue. The wrong ratio can also be caused by incorrect positioning of fake logs around the gas nozzles.